Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Fontana?
Chimney cap and crown work in Fontana typically runs $225 to $475 for a standard stainless cap installation, while a full crown rebuild generally falls between $700 and $2,200 depending on the crown’s size and how much of the masonry has broken down. Most Fontana homes need one or the other, and a good number need both once we get on the roof and see what’s actually going on. Call us at (833) 805-3229 for a free estimate before you commit to anything.
We sweep and repair chimneys across Fontana, from the older stucco ranch homes north of Baseline to the newer builds out toward Etiwanda, and the same two problems show up again and again: a rusted or missing cap letting water in, and a crown that’s cracked because it was poured too thin or never sealed. Neither one is expensive to fix early. Both get expensive when you wait.
Key Takeaways
- Standard chimney cap installation in Fontana: $225 – $475, installed and sealed.
- Custom caps for oversized or masonry chimneys: $450 – $900.
- Crown repair (patching cracks): $300 – $650.
- Full crown rebuild: $700 – $2,200.
- Crown plus cap done together on the same visit usually saves $75 – $150 versus booking them separately.
- Inland Empire heat and the occasional hard freeze cycle crack crowns faster than most homeowners expect. A hairline crack found at inspection costs far less than a roofline repair six years later.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s what each part of the job actually costs in the Fontana market as of this year. Ranges reflect real work, not teaser pricing. We source caps and crown materials from professional-trade suppliers like Olympia Chimney, Copperfield, Gelco, and Famco, which is why our numbers sit slightly above the bargain end of the market; the hardware lasts longer, and it fits.
| Line Item | Typical Fontana Range | What It Covers |
|---|---|---|
| Standard stainless steel cap | $225 – $475 | Single-flue cap, screened, installed and sealed to the flue tile |
| Custom or multi-flue cap | $450 – $900 | Fabricated to fit oversized or irregular chimney openings |
| Copper cap upgrade | $550 – $1,100 | Longer service life, higher wind resistance, premium finish |
| Crown crack repair (sealant / mortar patch) | $300 – $650 | Isolated cracks, sealing, minor re-slope |
| Crown rebuild, partial | $700 – $1,300 | Removing failing top course and re-pouring with proper overhang |
| Crown rebuild, full | $1,200 – $2,200 | Full crown removal, new form, reinforced pour, proper slope and drip edge |
| Cap + crown combined job | Saves $75 – $150 | Single visit, single setup, one roof access |
What pushes a Fontana job up or down? Three things matter most. First, roof pitch and access: a steep-pitch roof or a chimney tucked behind a patio cover adds setup time. Second, the condition of the flue tile at the top: if the crown has been leaking for years, water may have reached the tile and started spalling, which sometimes turns a crown job into crown plus liner work. Third, cap type: a basic stainless cap does its job for a standard flue. A copper cap or a custom-fabricated cap for a masonry chimney costs more but handles wind-driven rain the way an Inland Empire afternoon storm deserves.
If the crown has been failing for a while, water may have already reached the flue lining. That’s where a proper inspection matters, and where we can restore a deteriorating flue with HeatShield rather than documenting the problem and handing it off. Learn more about our full range of chimney services.
What Affects Chimney Cap & Crown Pricing in Fontana
- Roof pitch and chimney height. Fontana’s newer tract homes often have tall chimneys above low-pitch rooflines, which is fast to work on. Older custom homes with steeper roofs or second-story chimneys take longer to set up and cost more.
- Crown size. A small single-flue crown might need eight square feet of material. A wide masonry crown over a fireplace with multiple flues can take twelve or more, and the material and labor scale with it.
- How long the damage has been there. A fresh hairline crack is a patch job. A crown that’s been open to the weather for years may have a broken drip edge and loose material that needs to come off before anything new goes on.
- Cap material and customization. Standard stainless caps are the most cost-effective and last decades. Copper caps and custom-fabricated caps run higher but hold up better in the high winds around the Fontana foothills.
- Whether it’s really just the crown. Sometimes what looks like a crown problem is a crown problem plus a cracked tile or a failing liner. We check the whole flue while we’re up there rather than fixing the top and letting the real issue hide.
- Time of year. Spring and fall book the lightest. Summer heat and the pre-winter rush tend to be our busiest, and scheduling is tighter.
How Much Does a Chimney Cap Cost in Fontana, Separately?
A standard stainless steel chimney cap in Fontana runs $225 to $475 installed, screens included, sealed to the flue tile. That covers a single-flue cap on most homes.
Custom or oversized caps, and copper upgrades, start around $450 and can reach $1,100 for larger multi-flue chimneys. The cap itself is a small part of the total; the work is in the measurement, fabrication, roof access, and making sure the cap sits level and sealed so rain and animals stay out. We source our caps from professional chimney supply houses, not big-box stores, because a cap that rusts out in three years isn’t a savings. If you want to understand what a proper cap does before you buy one, our chimney cap and crown service in Fontana page walks through the specifics.
How Much Does Chimney Crown Repair Cost in Fontana?
Crown repair in Fontana comes in two flavors. Patching isolated cracks with a flexible sealant runs $300 to $650. A full crown rebuild, where the old crown comes off, the top of the chimney gets re-formed, and new mortar is poured with a proper slope and drip edge, runs $700 to $2,200.
The call between the two depends on what we find. If the crown is intact but cracked in a couple of places, patching works and lasts. If the crown is loose, has no drip edge, or has been letting water into the chimney for a long time, patching is throwing good money at a problem that’s going to keep coming back. Our crews rebuild crowns the same way professional chimney contractors do it: with a slope that drains water away from the flue, an overhang that keeps drips off the chimney sides, and a seal that survives freeze-thaw cycles. Fontana sees enough winter nights near freezing that a crown poured too thin will crack within a few seasons.
Is It Cheaper to Repair the Crown or Rebuild It?
Repair is cheaper short-term: $300 – $650 versus $700 – $2,200 for a rebuild. Repair is only the better value when the crown is largely sound. If the crown is cracked through, loose, or missing its drip edge, a patch buys you a couple of years before the same problem comes back, and the second time it’s usually worse.
We’d rather tell you honestly that a patch will work than sell you a rebuild you don’t need. And we’d rather tell you a rebuild is warranted than pat over a crown that’s already failing. Free estimate, no pressure either way. Call (833) 805-3229.
Can You Fix a Cracked Chimney Crown Without Replacing It?
Yes, in many cases. Cracks up to roughly a quarter-inch, and crowns that are still firmly attached with a sound drip edge, can usually be repaired with a flexible crown sealant that moves with the masonry. Crowns that are heavily spalled, crumbling, or have lost their slope need a rebuild.
We see a lot of Fontana homes where the crown is basically fine but the cap is missing, which is the source of the water that’s been cracking the crown in the first place. Fixing the crown without fixing the cap is fixing half the problem. That’s why we quote them together when both need attention.
How to Save on Chimney Cap & Crown Work in Fontana
There are real ways to keep the cost down, and a few that look like savings but aren’t.
- Do the cap and crown in one visit. Same roof access, same setup, one trip. That saves $75 to $150 on average compared to booking them separately, and in many cases the crew is already up there.
- Get the cap on before the crown fails. A cap is $225 to $475. A crown rebuild after years of uncapped water intrusion is $700 to $2,200, plus damage to the flue tile. The cheapest crown repair is the one the cap prevents.
- Book off-season. Late winter and early spring are lighter on our schedule, and we have more flexibility to work around your availability.
- Bundle with a sweep and inspection. A sweep and inspection is the right time to find crown and cap problems before they turn into bigger repairs. We do chimney sweep, dryer vent cleaning, and chimney repair under one call, so you don’t have to schedule three contractors for connected ventilation issues.
- Say yes to the free estimate. We’ll look at the cap and crown, and we’ll tell you whether a patch, a rebuild, or neither is the right answer. Call (833) 805-3229.
One thing we’d skip: bargain caps from retail channels. A cap that rusts out or lifts in a windstorm costs more to fix the damage from than the upgrade would have cost in the first place. We install caps made from the same professional-trade materials certified contractors specify.
When Should You Replace a Chimney Cap or Crown in Fontana?
Cap: when it’s rusted through, missing screens, bent, or lifting in wind. In Fontana, that often shows up after a wind event or after enough years of sun exposure that the finish is gone. Crown: when you can see cracks wider than a hairline, the crown feels loose when tapped, or there’s no visible overhang protecting the brick below.
One thing we check on every sweep is the crown. It’s the cheapest five minutes of the visit. Catching a crack early is the difference between a $300 patch and a $1,500 rebuild. If you haven’t had the top of your chimney looked at in a few years, this is the time. Our team handles the whole flue, from the crown down through the liner, and if a liner problem shows up we can restore it with HeatShield instead of recommending a full replacement. Read more about chimney repair in Fontana to see what that covers.
FAQs – Chimney Cap & Crown Cost in Fontana
How much does a chimney cap cost in Fontana?
A standard stainless steel chimney cap runs $225 to $475 installed in Fontana. Custom or copper caps range from $450 to $1,100. The price includes measurement, the cap, screens, sealing, and roof access. Call (833) 805-3229 for a free estimate.
How much does it cost to rebuild a chimney crown in Fontana?
A full crown rebuild in Fontana runs $700 to $2,200, with most single-flue jobs landing around $900 to $1,400. Partial rebuilds are $700 to $1,300; simple crack repairs are $300 to $650. Call (833) 805-3229 for an exact quote after we’ve looked at it.
Can I just patch a cracked chimney crown myself?
We don’t recommend it. A crown that’s patched without cleaning and prepping the crack, or patched with the wrong product, fails within a season or two in Fontana’s heat-and-freeze swings. More importantly, the crown is at the top of the chimney; if you’re not comfortable on a roof, don’t be up there. A professional patch is $300 to $650 and comes with a look at the flue tile while we’re at it. Call (833) 805-3229.
Do I need a cap if I have a crown?
Yes. They do different jobs. The crown keeps water off the brick and out of the chimney top from above. The cap keeps rain, animals, and debris out of the flue itself. A crown without a cap is a chimney still open to the weather. Most Fontana homes need both, and doing them together saves $75 to $150 on labor.
How long do chimney caps and crowns last in Fontana?
A quality stainless cap lasts 15 to 25 years; a copper cap typically lasts 40-plus. A properly rebuilt crown lasts 20 to 30 years if it’s poured with a proper slope and drip edge. The failure point in Fontana is the sun and the occasional winter freeze: caps rust, and thin crowns crack. A cap installed alongside a crown rebuild significantly extends the crown’s life by keeping the water off it. Call (833) 805-3229 for a free estimate.
Schedule a Free Estimate in Fontana
If your cap is missing, bent, or rusted, or your crown is cracked, the fix is straightforward and the price is knowable before anyone shows up. We’ll come out, look at the top of the chimney, and tell you what it needs (or what it doesn’t). We work with the same professional-grade materials certified chimney contractors use nationwide: DuraFlex liners, HeatShield restoration, and ventilation components from Olympia Chimney, Gelco, Famco, and Copperfield. One contractor handles the assessment, the sweep, and the repair, so there’s no handoff and no broken telephone between the inspector and the person doing the work.
Call (833) 805-3229 to schedule a free chimney cap and crown estimate in Fontana. If a dryer vent is also overdue, we handle that on the same visit; a clogged dryer vent is a fire-safety system, not an afterthought, and we treat it that way.
Pricing reflects the Fontana market as of 2026. Ashwood Chimney Sweep offers free estimates – call (833) 805-3229.
What Our Customers Say
"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
— Alejandro Garcia"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
— Paul Padgett"They were the only ones willing to just tell me the price. Everyone else wanted to "come take a look" first, which in my experience means come apply pressure in person."
— Marisol Salazar